How To Remove Oven Bottom Panel

All is well in the kitchen with a working oven. When the oven starts showing error codes, or even goes completely expressionless, and so it can be a struggle to put a decent meal on the table.

If y'all've run into these symptoms, then you may have done some troubleshooting and determined that the electronic command board (aka electronic range control - ERC) needs to be replaced or repaired.  That sounds simple enough provided you can get the board out of the oven. Otherwise, you might take to telephone call an appliance technician to come remove information technology for you.

In this article, we provide an illustrated example of a 5-10 minute functioning for extracting the board and then you don't have to pay the $40-$100 service fee for a tech to practise the same thing.

This post specifically shows a common G.E. wall oven/microwave combo unit, just a broad variety of brand proper name appliances (Whirlpool, KitchenAid, Kenmore, JennAir, etc...) are configured very similarly.

1. Plow off power to the appliance

You're going to expose wiring connections that supply upwardly to 240VAC - lethal!  Plough off the billow for the oven to avoid any tragedy.

2. Open the door and remove the mounting screws

Open the door and look at the inner trim on both sides. Typically, at that place are two screws on each side that are holding the oven in place confronting its cutout in the wall. These wood screws tin be tight - y'all may want a ability drill to remove them. Be sure not to strip the screw heads.

3. Slide the unit out from the wall

Grab onto the oven chassis and wiggle it out from the wall. You only need to move information technology out a few inches, until yous tin can come across spiral heads on the outer trim.

4. Remove the side trim and panel screws

Accept the outer trim off by removing the screws. There may too exist some screws running along the bottom of the command panel - remove these every bit well.

five. Drop downward the control panel

Now, you should be able to loosen the control panel from the oven and swivel it down. Be careful non to let it completely succumb to gravity so it doesn't yank on the wiring or drop down to the floor.

6. Document the wiring connections

In one case the control panel is down, you'll meet the control board mounted on the backside of the console. There volition be a lot of wiring connections to the board. We strongly recommend you document how everything is connected so you lot can be sure to install the board correctly afterward repair. Some good methods include:

• Take pictures of the wiring
• Flag each wire with a piece of tape and its own number/letter
• Sketch out a diagram of where each wire goes

7. Disconnect the wiring and remove the control board from the console

Pull the wires off their terminals on the board. Sometimes the wiring connectors tin be pretty tight. Consider using needle-nose pliers to grab a hold of the spade terminal on the stop of wire. Or, you can use a small flathead screwdriver to pry the wires away from the board.

*** The sparse "record-like" ribbon cable is fragile!  If this gets damaged, you will accept to replace the control console/keypad.  Gently squeeze the tabs on the connector where the ribbon cablevision is inserted and lift the cablevision away from the lath.Avoid creasing the cable.

8. Package and send the board in for repair

These command boards tend to have frail drinking glass displays which cannot be replaced anymore.  Make certain to supply ample cushioning effectually the control board when packaging information technology in a box for shipping.  Use bubble wrap, styrofoam, newspaper, etc.

So head to ApplianceBoardRepair.com and find your model/office number to get a shipping characterization!

9. Leave power to the unit off until the board is returned

At present that there are a agglomeration of loose wires dangling in the apparatus control cabinet, it would be wise to leave the ability off until they can be safely secured dorsum on the control lath.  If you lot actually need to plough that breaker back on, wrap each loose wire end with plenty of electric tape to make sure no high voltage terminals brusk to each other or the oven chassis.

Source: https://applianceboardrepair.com/a/blog/how-to-remove-an-electronic-control-board-from-a-built-in-wall-oven

Share this post