How To Remove Jets From Tub

Cleaning the jets in your hot tub is a crucial part of your hot tub'due south maintenance. If the jets are left unchecked and muddy, they tin get blocked by a buildup of debris and grime in the hot tub. Having your hot tub jets blocked past debris and grime creates dissimilar problems.

Non merely does information technology put you at risk of dissimilar health issues and water-borne illnesses, but it also reduces the effectiveness of your hot tub'southward jets. Then, how to clean hot tub jets? Let's find out.

How Often Do You Need to Clean Hot Tub Jets?

You should clean hot tub jets every iv-vi months if you don't use the hot tub regularly. If yous use the hot tub regularly, you need to clean hot tub jets every 2-3 months.

The hot tub waterline should exist filled in a higher place every jet, which means that the jets will exist in contact with the water all the time. The water also circulates through the jets all the time, which besides means that all the grit, debris, and dirt will go through the hot tub jets.

Just similar your hot tub h2o, the hot tub jets volition as well get muddy, and in some cases also clogged. That's why it's recommended to make clean hot tub jets so ofttimes.

Method 1: Clean Hot Tub Jets By Removing Them

In that location are two principal ways to clean the jets in your hot tub. You can either remove the jets from the hot tub and clean them or make clean the jets without removing them from the hot tub.

Both methods if executed properly volition ensure the jets are clean and grime-free. But in that location are a few steps to follow while executing both methods. Let's check out the get-go method.

This method involves removing the hot tub jets from their positions and cleaning them after. Only how do you lot get well-nigh this?

1. Turn Off the Hot Tub and the Jets

The offset affair to practice is to turn off the jets and the hot tub. Y'all tin use the control panel to plow off the jets and you can unplug the hot tub or plow off the GFCI billow.

The GGCI breaker of your hot tub is usually located away from the hot tub and information technology's the device that ensures your hot tub gets ability. Ensure to turn off the jets by using the control panel of your hot tub. Then turn off the GFCI breaker because water and electricity aren't exactly the best of friends.

2. Unscrew the Jets From the Sockets

The side by side thing to do is to unscrew the hot tub jets. To exercise this, you might need a wrench and, or a screwdriver. You can cheque the transmission of your hot tub for instructions on how to remove the jets.

Ordinarily, you will merely need to rotate the jets in an anticlockwise direction until you run across the jet pop out. If you can't get a good grip on the jets with your easily, you can employ a wrench to unscrew the jets. Simply get a good grip with the wrench and turn anticlockwise till you can pull the jet out of its socket.

If the jets in your hot tub were screwed down with screws or nuts, you will need to remove them offset. This is where the screwdriver will come in handy. Ensure y'all know where you removed each jet from, so you can spiral information technology dorsum in identify correctly.

Depending on the size of your hot tub, removing the jets might accept you a few minutes or longer. Larger hot tubs like the 7-viii person hot tubs usually take several jets and unscrewing them all will accept a while. And so, prepare yourself for the task ahead.

two. Mix Water and Vinegar

Mix a few tablespoons of vinegar in a bucket of h2o. And so mix thoroughly. You can also add together a bit of powdered dishwasher detergent to the mixture or a tablespoon of bleach.

But ensure you lot don't add together too many acidic products. Detergent, bleach, Vinegar, and the likes have a very acidic level. Adding too much of these products to the h2o can corrode the jets.

If you don't want to mix all of these or you are worried nigh the acidic content of the mixture, you can buy jet cleaning chemicals from your local hardware store or local pool shop.

The jet cleaning chemicals have been especially formulated to clean jets without corroding or dissentious them but they will cost you lot a bit of cash.

3. Soak the Jets in the Solution or Chemical

The adjacent matter to practice is to soak the jets in the mixture or the jet cleaning chemical. Simply put the jets one after the other within the chemical or solution and leave them for a while.

Depending on how dirty or clogged the jets are, you can soak them for a few minutes or a few hours. You lot can fifty-fifty soak the jets overnight. Ensure the jets are well submerged inside the chemical or solution.

The acidic content of the mixture of the chemical will break downwardly and remove mineral deposits and crud inside the jets. The grime in the jets may take accumulated or solidified over time. The chemicals volition interruption them down so they are easier to clean.

4. Use a Brush to Scrub the Jets

Subsequently soaking the jets for the required fourth dimension. Remove them from the chemical or solution and scrub the internal parts of the jets with a brush. This will ensure all the debris and grime within the jets are removed. Scrub the jets till you lot can't notice any grime inside them but exist gentle.

5. Rinse the Jets

After scrubbing the jets, yous should rinse them in clean water or spray them with a hose. Ensure the jets are properly rinsed considering any chemical or solution left on the jets can cause foamy or cloudy water inside your hot tub.

The chemicals and solvents used to make clean the jets will mix with the water in the tub when you replace the jets and this tin can crusade cloudy spa h2o. This tin also corrode other parts of the hot tub similar the media in the filtration organization.

6. Return the Jets

When the jets take been properly rinsed, you can return them into the hot tub. Over again, ensure to put each jet where you removed information technology. Yous should also ensure the jets are screwed in tight then they don't come up off when you turn them on.

Afterward returning the jets into the hot tub, plough on the GFCI breaker and turn on the jets on a low setting to cheque if they work properly. If they work fine, you can switch the jets to run on a loftier setting for about 20 minutes. If everything works fine, then you tin can rest bodacious the jets have been well cleaned and replaced.

If you plough on the jets either on a depression setting or on a loftier setting and you tin can hear loud vibrating noises, try to spot the jet making the noise and set up it in properly. Chances are you lot did not screw the jet properly. That's why it was making the dissonance.

The chief advantage of removing the jets and cleaning them is that you can be sure the jets are properly cleaned before screwing them back in. You also get to know which of the jets is damaged, dented, or needs to be replaced.

Now, let's check out the other method.

How To Clean Hot Tub Jets (Without Removing Them)?

Another method to make clean your hot tub jets is to make clean them while inside the hot tub. For this method, you lot wouldn't need to remove the jets.

You just need to add a jet cleaning chemical or solution to the hot tub h2o and let the water broadcast through the jets. Only that'southward only the quick answer. Permit's check out this method in full detail.

1. Heat the Water

You demand the jets on and working while you make clean them. Earlier turning on the jets, ensure the waterline is higher up every jet.

The water in your hot tub should already be hot. If the water isn't hot for some reason. Ensure to plough on the heater and permit the water temperature rise to nearly 100 degrees Fahrenheit (or 38 degrees Celsius).

This might have a while if the water in the hot tub is cold. It might even take upward to viii hours or more than for the heater to fully heat the water temperature to the needed level.

two. Add a Jet Cleaner to the Water

While the water is being heated and the jets are running, you should add a jet cleaning solution or a jet cleaner to the water in the hot tub.

The jet cleaner should be added to the water in the right quantity. Check the instructions on the container of the jet cleaner to know how much cleaner you need to add to the water.

If you don't want to use a jet cleaner or y'all don't have ane nearby, y'all tin can add powdered dishwasher or detergent to the water. You can also add together two or three tablespoons of bleach to the water in the hot tub for a thorough make clean of the jets.

As an skillful tip, you shouldn't add together too much bleach or detergent to the water in the hot tub. It'southward not ideal to add together such acidic products to the water in your hot tub because these products can disrupt your h2o chemistry and they tin can also damage the filters, headrests, the shell, and other parts of your hot tub. So, your best bet is to get with a jet cleaner. Only utilise bleach or detergent as the terminal resort.

3. Let the Jets Run on High

Afterwards calculation the jet cleaner to the water, let the jets run on a loftier setting for about 15 to xx minutes. Turning on the jets on high will ensure the h2o is well circulated through every jet in the hot tub. As the water circulates and flows through each jet, the active chemicals in the jet cleaner will break downwardly and dissolve every grime and mineral deposit inside the jets.

The chemicals are commonly potent plenty to dissolve oils, slime, dirt, and grime that might accept accumulated inside the hot tub's jets. As the chemical breaks down the crud in the jets, the dissolved particles are flushed out equally the water circulates.

These particles will also exist picked up by the filtration system of your hot tub. Afterwards turning on the jets on high, switch it to a low setting and allow the jets run also. Alternate between the depression and high setting for about an hour. Then turn off the jets.

Related Read: Can Y'all Use Hot Tub Jets With the Cover On?

4. Clean the Filters

The grime flushed out of the jets will near likely be picked up by the filters in the hot rub. So after turning off the jets, take out the filters and clean them properly with h2o or a filter cleaner.

v. Bleed the Hot Tub

Aye, you should drain the hot tub, especially if you added bleach and other acidic products to the h2o. You don't want to take a soak in such water. Doing that volition cause skin irritation. There is a drain valve at the base of operations of your hot tub. You can turn the valve or remove information technology to drain the water.

half dozen. Fill the Hot Tub With Common cold H2o

After draining the hot tub, refill it with cold water. You don't need to turn on the heater this time. But plough on the jets and let them run for xx to xxx minutes. This will rinse the jets and get rid of all crud and chemicals in the jets. After this, drain the hot tub again.

And then refill it with clean water and heat the h2o. You should also add together sanitizers to the h2o afterwards this and vacate the hot tub for near 24 hours before using it. This will ensure the jets are squeaky clean.

Tin can You Clean Hot Tub Jets With Magic Eraser?

Yeah, y'all tin can employ magic eraser to clean hot tub jets. But, you should only practise this if yous remove the jets from the hot tub beginning.

Just fill up an empty basin with water and magic eraser and put the jets there. Leave them for at to the lowest degree thirty minutes and take them out. Magic eraser will make all the dirt and mineral accumulation disappear. Subsequently that, yous demand to properly rinse the hot tub jets before putting them back on the hot tub.